We have solution for you

WE ARE KNOWN FOR

  • Having experience.
  • Being independent from different manufacturers.
  • Being fast.
  • Having parts on time like requested.
  • Making high quality service to repair the equipment.
  • Being in the whole industry

Parker Senso Control Diagnostic Equipment

Standardized measuring equipment on different machines enables to makes comparisons between different types of machines.

We provide sensors to record all main parameters and different solutions to store it into a recording history.

Service Master with special adapter boxes

The new designed hydraulic systems contains highly efficient components.

With ultrafast Proportional valves and controllers, the machines will be able to have shorter cycles and more precisely functions.

To ensure the proper function it is required to check the function periodically with applicable measuring systems.

The Service Master measuring system is able to measuring and store all relevant parameters of the valve and by its various capabilities its possible to reduce and locate failures on the checked valves.

To use it as a preventive check, it is possible to compare the performance parameters from measurements before to the current checks.

Test point connectors Ermeto DIN

The measurement of high rated pressure meets special challenges.

To guarantee a proper measurement, its not enough to observe the nominal pressure of the system.

Also it is required to calculate the requested sampling rate of the measurement and possible maximum pressure peaks.

Oblivion of the conditions results to measurement failures.

Only highly rated measurement test point connectors can keep the conditions.

Laser alignment equipment for heavy machines

A proper alignment of the injection unit is the basic request for stabile results of the injection unit.

Finally, the alignment has to be checked between the centre of injection piston-rod and the current assembled shot-sleeve in full closed position of the machine.

The existing optical measurement systems cannot fulfill that request, because that kind of measurement is doing on site of the Fixed Platen only in the open position of the machine.

So movements of the Fixed Platen, of the die and of the shot sleeve in the moment of closing of the machine stay out of measurement.

To find really valid results, we offer the check of the alignment by our laser-based system.

Here we assemble the sender directly on the shot sleeve and the receiver will be moved 120 degrees around the injection piston-rod.

With this system, which is developed by the German Specialists of company Prüftechnik, we set 5 points in the angle of 120 degrees and after the measurement the evaluation unit shows and save the declination of the centre axis.


Notice: Trying to access array offset on value of type null in /home/powerserviceteam/public_html/inc/subservicios.php on line 37

Profibus / Profinet Analizer

New electrical controlled equipment often is connected via Siemens Profibus or Profinet.

Beside the advantages of those connections, it is difficult to find communication problems in the systems.

We have the equipment to analyze the data transfer and failure rates in the systems by connection of a Profibus or Profinet tester.

This equipment not only do identify a problem but also let you have a certification of the whole data network on the machine and we are able to say, in which distance of a connecting exchange point the estimated problem is to find.

Diecast Injection Analizer with Rate of 2kHz

Due to tough international competition, increased customer demands and legal requirements demand a respective quality management system.

Modern process data measuring systems enable a safe controlled production.

The best feasible solution is to connect the data measuring system into the control of the machine.

This gives a possibility to limit the failures of the machine.

Combined with a new control, the industrial computer of the measuring system is used for the human-machine-interface and gives the possibility to save money.


Notice: Trying to access array offset on value of type null in /home/powerserviceteam/public_html/inc/subservicios.php on line 114

Flow Meters and controls for High Temperature water and oil

In the casting processes of parts, the temperature-flow of the die is a main parameter of the casting process.

The simplest way is to check the temperature of the heat transfer medium.

But this do not take a guarantee to have also the right quantity of heat transfer.

Only with flow meters in the return conduction there is a safety to see temperature problems before they will cause to differently parts quality.

The flow meters must be able to be connected in high temperature environment and also for temperature transfer medium like heating oil.